User Tools

Site Tools


tailorcrete:examples:el_caleyo

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
tailorcrete:examples:el_caleyo [2012/07/18 16:54] kolarfiltailorcrete:examples:el_caleyo [2012/09/13 10:22] (current) – Language check, formatting bp
Line 1: Line 1:
-  * **El-Caleyo simulation**+===== El-Caleyo simulation =====
  
-So called El-Caleyo wall is special formwork with holes and angles designed to test filling ability of self-compacting concrete (SCC)Geometry of the formwork is on the picture below+==== Test Setup and Geometry ==== 
 +This example illustrates the casting simulation of real problem. The test has been designed by El-Caleyo. The purpose of this tests is to assess the filling ability of self compacting concrete in complex formworks with complex geometry, containing several holes and rather dense traditional reinforcementThe geometry of the formwork is illustrated in Fig.1
  
-{{:tailorcrete:examples:elcaleyo_geometry.jpg?200|}}+|{{:tailorcrete:examples:elcaleyo_geometry.jpg?200|}}
 +|Fig.1: The geometry and setup of El-Caleyo wall|
  
-Simulations were done in two different ways of casting. In the first case, SCC is casted from the bottom of the specimen with constant input velocity. In the second case, SCC is casted from the top as it is usual in real casting.+==== Computational Model ==== 
 +Simulations were done for two different casting setups. In the first case, the SCC is pumped from the bottom of the specimen with prescribed constant input velocity. In the second case, SCC is casted from the top.
  
-    * Casting from the bottom+=== Casting from the bottom ===
  
-Example of input file for the "bottom casting" is here: {{:tailorcrete:examples:elcaleyo.oofem.in|}}+Example of OOFEM input file for the "bottom casting" sumulation can be dowloaded from here: {{:tailorcrete:examples:elcaleyo.oofem.in|}}
  
-On the next picture, scheme of "bottom casting" is shownThere is is prescribed velocity at the bottom edge.+== Results == 
 +Initial setup of the model: 
 +|{{:tailorcrete:examples:el_caleyo_t0.0.png?200|}}|
  
-{{:tailorcrete:examples:el_caleyo_t0.0.png?200|}} 
  
-Situation for evolving time is captured on pictures below: 
  
-{{:tailorcrete:examples:el_caleyo_t25.0.png?200|}}+The snapshots of solution, illustrating the position of SCC in different times, are presented below. 
 +|{{:tailorcrete:examples:el_caleyo_t25.0.png?200|}}|{{:tailorcrete:examples:el_caleyo_t100.0.png?200|}}| 
 +|{{:tailorcrete:examples:el_caleyo_t175.0.png?200|}}|{{:tailorcrete:examples:el_caleyo_t400.0.png?200|}}|
  
-{{:tailorcrete:examples:el_caleyo_t100.0.png?200|}}+=== Casting from the top ===
  
-{{:tailorcrete:examples:el_caleyo_t175.0.png?200|}}+Example of OOFEM input file for the simulation "casting from the top" can be dowloaded from here:{{:tailorcrete:examples:elcaleyo_top_oofem.in|}}
  
-{{:tailorcrete:examples:el_caleyo_t400.0.png?200|}}+On the next picture, casting scheme is shown. SCC is initially at the reservoir above the wall:
  
-  * Casting from the top +|{{:tailorcrete:examples:el_caleyo_casting_from_the_top_t0.0.png?200|}}|
- +
- +
-Example of input file for the "casting from the top" is here:{{:tailorcrete:examples:elcaleyo_top_oofem.in|}} +
- +
-On the next picture, casting scheme is shown. SCC is initially at the reservoir above the wall. +
- +
-{{:tailorcrete:examples:el_caleyo_casting_from_the_top_t0.0.png?200|}}+
  
  
tailorcrete/examples/el_caleyo.1342623263.txt.gz · Last modified: 2012/07/18 16:54 by kolarfil